欢迎来到信誉一分彩网投大平台官方网站!
全国咨询热线0531-84277123
您的位置: 首页>> 产品中心 >>固定升降平台

固定升降平台生产厂家

维保时间的规定 Provision of maintenance time 、日常保养(每班进行)。 Daily maintenance (per shift). 升降机工作1500小时后,对机械、电气系统进行小修。

在线咨询 服务热线15628816012

产品详情

维保时间的规定
Provision of maintenance time
、日常保养(每班进行)。
Daily maintenance (per shift).
升降机工作1500小时后,对机械、电气系统进行小修。
After working 1500 hours, the elevator undertakes minor repairs to mechanical and electrical systems.
升降机工作5000小时后,对机械、电气系统进行中修。
After 5000 hours of work, the elevator will be repaired in the middle of mechanical and electrical systems.
升降机工作10000小时后,对机械、电气系统进行大修。
After 10,000 hours of work, the elevator overhauled its mechanical and electrical systems.
设备维护与保养
Equipment Maintenance and Maintenance
各机构的制动器应经常进行检查和调整制动瓦和制动轮的间隙,保证灵活可靠。在摩擦面上,不应有污物存在,遇有污物必须用汽油或稀料洗掉。
The brakes of various agencies should be checked and adjusted regularly to ensure flexibility and reliability. On the friction surface, there should be no dirt. If there is dirt, it must be washed off with gasoline or dilute material.
减速箱、变速箱、外啮合齿轮等各部分的润滑以及液压油均按润滑表中的要求进行。
The lubrication and hydraulic oil of gearbox, gearbox, external meshing gear and other parts are carried out according to the requirements of the lubrication table.
要注意检查各部钢丝绳有无断丝和松股现象。如超过有关规定必须立即换新。钢丝绳的维护保养应严格按GB5144-85规定。
Attention should be paid to checking whether there are broken wires and loose strands in each wire rope. If it exceeds the relevant provisions, it must be renewed immediately. Maintenance of steel wire rope should be strictly in accordance with the provisions of GB5144-85.
经常检查各部的连接情况,如有松动应予拧紧。机体连接螺栓应在机体受压时检查松紧度(可采用旋转臂的方法去造成受压状态),所有连接稍轴都必须有开口销,并需张开充分。
Check the connection of each part regularly, and tighten it if it is loose. The body connecting bolts should be checked for tightness when the body is under pressure (the compression state can be caused by the method of rotating arm). All connecting slightly shafts must have open pins and be fully opened.
经常检查各机构运转是否正常,有无噪音,如发现故障,必须及时排除。
Regular inspection of the normal operation of institutions, whether there is noise, such as fault detection, must be eliminated in time.
安装、拆卸和调整回转机构时,要注意保证回转机构减速器的中心线与齿轮中心线平行,其啮合面不小于70%,啮合间隙要适合。
When installing, disassembling and adjusting the rotary mechanism, attention should be paid to ensuring that the center line of the reducer of the rotary mechanism is parallel to the center line of the gear, and its meshing surface is not less than 70%, and the meshing clearance should be suitable.
经常检查所有的电线、电缆有无损伤。要及时的包扎和更换以损伤的部分。
Check all wires and cables regularly for damage. The damaged parts should be dressed and replaced in time.
遇到电动机有过热现象要及时停车,排除故障后再继续运行,电机轴承润滑要良好。
When the motor is overheated, stop in time and continue to run after troubleshooting. The lubrication of motor bearings should be good.
各部分电刷,其接触面要保持清洁,调整电刷压力,使其接触面积不小于50%。
The contact surface of each part of the brush should be kept clean, and the pressure of the brush should be adjusted to make the contact area not less than 50%.
各控制箱、配电箱等经常保持清洁,及时清扫电器设备上的灰尘。 11.各安全装置的行程开关的触点开闭必须可靠,触点弧坑应及时磨光。
The control boxes and distribution boxes are often kept clean, and dust on electrical equipment is cleaned in time. 11. The contact opening and closing of the travel switch of each safety device must be reliable, and the contact arc pit should be polished in time. 

信誉一分彩网投大平台大型济南液压升降机厂家,青岛电动升降平台厂家,淄博液压升降平台厂家,枣庄液压升降机厂家,东营液压升降平台厂家,烟台液压升降机厂家,潍坊液压升降平台厂家,济宁液压升降平台厂家,泰安电动升降机厂家,威海液压升降平台厂家,日照电动升降机厂家,滨州液压升降平台厂家,德州电动升降机厂家,聊城液压升降平台厂家,临沂液压升降机厂家,菏泽液压升降平台厂家,莱芜液压升降机厂家,临沂电动升降机厂家需要的朋友欢迎采购0531-84277123 文章来源:

热品推荐
XML 地图 | Sitemap 地图